블로그로 돌아가기
사용 방법 가이드 2026-11-15 Les Tissées – Curated Fashion Fabrics 1 조회수

How to Sew Swim Fabric With a Lining: Step-by-Step Guide

How to Sew Swim Fabric With a Lining: Step-by-Step Guide

Learn how to sew swim fabric with a lining, from choosing the right 4-way stretch materials to stitching, fit checks, and care for a swimsuit that lasts.

Start with two fabrics that move together

Sewing swimwear with lining starts with a simple rule: the outer fabric and the lining must both stretch in four directions. If one restricts the other, the finished swimsuit will pull, twist, or feel tight even when the pattern fits. Choose a swim fabric and a swimsuit lining fabric that are both 4-way stretch, then treat them as a pair throughout the project.

For the outer layer, a fabric like Les Tissées' 4-Way Stretch Swim Fabric | Coastal Cutouts | Multi gives you approximately 40% four-way stretch, a smooth hand, and chlorine and salt water resistance. For the inside, the Swimsuit Lining Fabric is a lightweight 4-way stretch lining made from 92% polyester and 8% spandex. Together they support close-fitting swimwear without fighting each other.

What the outer swim fabric gives you

What the lining contributes

  • Swimsuit Lining Fabric: 92% polyester / 8% spandex, 154 cm (60") wide, 130 gsm (3.83 oz/yd2), 4-way stretch. At 130 gsm it adds coverage without bulk, and its 4-way stretch lets it move with the outer swim fabric instead of restricting it.
    Swimsuit Lining Fabric
    Swimsuit Lining Fabric
  • Swimsuit Lining Fabric: Available in Nude, Light Beige, White, and Black; sold by 0.50 metre (0.54 yard) increments, cut continuously when possible. You can match the lining to your outer fabric or choose a neutral, and order the total length you need for full or partial lining.

Before you cut: pattern and quantity checks

  • Check your pattern's lining requirements: Some sewing patterns call for full lining, while others require lining only in specific areas. Always check the fabric requirements included with your sewing pattern before ordering, because the amount of lining needed depends on style, size, and whether the swimsuit is fully or partially lined.
  • Plan for continuous cuts: Both fabrics are sold in 0.50 metre (0.54 yard) increments, and multiple quantities will be cut in one continuous piece whenever possible. Add up your pattern pieces before ordering so you receive a single length rather than seams in the middle of a panel.
  • Pre-wash the lining as you will wash the garment: The supplier recommends pre-washing your fabric the same way you intend to wash your finished garment. Do this before cutting so any change in the lining happens before it is sewn in.

How to sew swim fabric with lining, step by step

The sequence below keeps the lining and outer fabric aligned and lets you check fit before finishing edges. It assumes a pattern that calls for lining; follow your pattern's specific construction order where it differs.

  1. Set up for stretch: Use a stretch or ballpoint needle and a stretch-compatible stitch or serger, as recommended for the Swimsuit Lining Fabric. The same setup suits the 4-way stretch swim fabric.
  2. Cut outer fabric and lining: Cut matching pieces from the swim fabric and the lining according to your pattern. Keep the greatest stretch direction consistent between the two layers so they stretch together.
  3. Baste or clip the layers together: Treat the lining and outer fabric as one unit at seam lines. Avoid stretching the fabric while sewing to help maintain its original shape, especially on the lightweight lining.
  4. Sew main seams without pulling: Stitch with a stretch-compatible stitch or serger, letting the fabric feed evenly. Do not stretch the fabric as you sew; the 4-way stretch is built in, and pulling distorts the seam.
  5. Check fit and coverage before finishing: Try the swimsuit on or compare it to your measurements before hemming or attaching elastic. The lining should stretch with the main swimwear fabric so it does not restrict fit or movement.
  6. Finish edges and care for the garment: Complete hems and openings according to your pattern. For the lining, hand wash in cold water and dry flat. Pre-washing the outer swim fabric the same way you plan to wash the finished swimsuit is also recommended.

When to line fully and when to line selectively

Not every swimsuit needs to be fully lined, but adding a swimsuit lining can provide additional coverage and create a cleaner interior finish. Full lining is common for one-piece swimsuits, while bikinis, swim tops, and swim bottoms may use lining only in specific areas as your pattern directs. The Swimsuit Lining Fabric is suitable for bikini tops, bikini bottoms, one-piece swimsuits, and other swimwear projects.

Use the lining weight as a guide: at 130 gsm it adds a layer of coverage while maintaining flexibility. If you are sewing a very fitted style, confirm that your pattern's lining pieces match the outer pieces in stretch direction, and avoid substituting a non-stretch lining, which would restrict the garment.

Care that keeps both layers performing

The Swimsuit Lining Fabric should be hand washed in cold water and dried flat. The outer swim fabric is chlorine and salt water resistant, which helps maintain its vibrant colors, softness, and shape season after season, but rinsing after salt or chlorine exposure is still a sensible habit. Pre-wash both fabrics the same way you intend to wash the finished garment before you cut, so the lining and outer layer shrink or relax consistently.

Avoid stretching either fabric while sewing; this is especially important on the lightweight lining, where pulling can distort the shape before the garment is even worn. If you need help choosing a style, Les Tissées offers PDF sewing patterns for inspiration.

관련 게시글

Customer Service
홈
상품
장바구니
내 정보