Back to Blog
How-to Guides 2026-11-02 Les Tissées – Curated Fashion Fabrics 2 views

How to Sew Printed Mesh Fabric: Abstract Faces Deadstock Guide

How to Sew Printed Mesh Fabric: Abstract Faces Deadstock Guide

A step-by-step method for sewing lightweight printed mesh deadstock, from needle and stitch choice to stabilizing seams and protecting the abstract print.

Quick answer

Sew lightweight printed mesh with a fine ballpoint or stretch needle, a narrow zigzag or overlock stitch, and a strip of stable seam tape at any edge that will take strain. Test on a scrap first, because the print and the open mesh structure both hide mistakes until the seam is under tension.

Why lightweight printed mesh behaves differently from solid knits

A printed mesh is usually a thin, open polyester knit, so it stretches, curls at cut edges and shows every wobble in a seam. The abstract print adds a second problem: a skipped stitch or a puckered line disappears into the pattern, so you cannot rely on visual inspection alone. Handle the fabric as little as possible before sewing, and keep cut pieces rolled rather than folded so the print does not crease along the fold line.

Because the mesh is sheer and lightweight, seam bulk matters more than seam strength in most garments. A bulky seam will show through the right side, while a narrow, well-tested seam disappears. That trade-off is why the steps below favor fine needles, short stitch lengths and minimal seam finishing rather than heavy reinforcement everywhere.

Where printed mesh works best, and where it does not

Printed mesh earns its place in overlays, sleeves, panel inserts, lingerie and costume layers where you want pattern without weight. It is a poor choice for a structured bodice or a garment that must hold a sharp pressed crease, because the open knit will not support either. If you need opacity or shape, plan a solid lining or underlayer instead of trying to make the mesh do that job.

Step-by-step: sewing abstract print mesh

  1. Pre-wash and dry a test square: Cut a 20 cm square, wash and dry it the way you will treat the finished garment, then check for shrinkage, print fading and edge curl. Common mistake: skipping this because deadstock quantity is limited, then discovering the mesh puckers after the first wash. If the test square changes size or the print dulls, adjust your fit allowance or choose a different project before cutting the main piece.
  2. Stabilize the cut edges before they curl: Spray or lightly starch the mesh, or fuse a narrow strip of lightweight knit interfacing along edges that will be sewn under strain. Let it dry flat. Common mistake: stretching the mesh while handling it wet, which sets a wavy edge. Stabilize only the seam allowance, not the whole piece, so the mesh keeps its drape.
  3. Choose a fine ballpoint or stretch needle: Use a size 70/10 or 75/11 ballpoint or stretch needle and a polyester or polyester-cotton thread. Sew a test seam on a scrap at your intended stitch length. Common mistake: using a universal needle that pushes the knit instead of parting it, causing skipped stitches and holes. If you see holes along the stitch line, change the needle before changing the thread.
  4. Set a narrow zigzag or overlock stitch: For a standard machine, use a narrow zigzag (about 0.5–1 mm wide, 2–2.5 mm long) or a stretch stitch; for an overlock, use a 3-thread narrow seam. Sew a test seam and pull it gently to check recovery. Common mistake: using a straight stitch, which snaps when the mesh stretches. The seam should stretch without breaking; if it cracks, widen the zigzag or shorten the stitch slightly.
  5. Sew with light pressure and support the fabric: Lower the presser foot pressure if your machine allows, place tissue paper under the seam if the feed dogs drag the mesh, and sew slowly. Common mistake: pulling the fabric from behind the needle, which stretches the seam and distorts the print. Let the feed dogs move the fabric; your hands should guide, not pull.
  6. Finish seams without adding bulk: Trim seam allowances to about 6 mm, then either overlock the raw edges or leave them narrow and clean-finished with a second zigzag row. Common mistake: pressing a heavy seam open, which leaves a shine or a ridge visible through the sheer mesh. Press seams lightly on a scrap first to confirm the polyester does not shine or melt.
  7. Check the print alignment before final stitching: Pin or baste the seam, then view it from the right side against a light to confirm the abstract faces line up as intended. Common mistake: sewing the seam fully before checking, then having to unpick a stretch stitch that leaves needle marks. Baste first on any seam where the print is the focal point; unpicking mesh is slow and can leave permanent holes.

Product facts for this project

  • Designer Deadstock Printed Mesh Fabric | Abstract Faces: Lightweight 100% polyester mesh, 150 cm / 59" wide, with an abstract faces print in blue, orange, black, white and lime. The wide lightweight polyester base suits overlays and sleeves, while the bold multi-color print makes seam puckering and skipped stitches harder to spot, so test seams before committing.
    Designer Deadstock Printed Mesh Fabric | Abstract Faces
    Designer Deadstock Printed Mesh Fabric | Abstract Faces

Related Articles

Customer Service
Home
Products
Cart
Profile